ISO 18286 PDF

ISO specifies requirements for tolerances for hot-rolled stainless steel plates (quarto plates) made on a reversing mill with the following. EN & ISO Tolerances for COLD Rolled material (Sheets, plate, coil) up to mm thick. EN & ISO Tolerances for ‘Quarto’ Hot. ISO. Second edition. Hot-rolled stainless steel plates —. Tolerances on dimensions and shape. Tôles en acier inoxydable laminées à chaud.

Author: Akitilar Nim
Country: Senegal
Language: English (Spanish)
Genre: Literature
Published (Last): 6 October 2010
Pages: 97
PDF File Size: 1.33 Mb
ePub File Size: 14.37 Mb
ISBN: 563-5-34612-749-6
Downloads: 95080
Price: Free* [*Free Regsitration Required]
Uploader: Nikozil

Take the smart route to manage medical device compliance. This meant that most stainless steels fell into steel type L. It can be argued that neither standard is completely consistent on this subject. We use cookies to make our website easier to use and to isp understand your needs. An approximate comparison is shown in the following table for a 10mm plate in various grades of steel using the mm measuring length:. Accept and continue Learn more about the cookies we use and how to change your settings.

Tolerances to ISO for hot rolled stainless steel quarto plates General This standard covers hot rolled stainless steel plates rolled on a reversing mill known as quarto plate.

For example, martensitic grades in the quench and tempered condition or high yield strength PH grades are expected to have a better flatness than You may experience issues viewing this site in Internet Explorer 9, 10 or Please download Chrome or Firefox or view our lso tips. Thickness The tolerance under nominal thickness is 0. Worldwide Standards We can source any standard from anywhere in the world. It may also be taken to cover plate rolled on a Steckel mill but taken out of the process before coiling has begun.

  JUNJI ITO GYO PDF

Article: Tolerances to ISO for hot rolled stainless steel quarto plates

Click to learn izo. There are no tolerances on the maximum difference allowed within a plate. Even the nitrogen strengthened steels were in this type.

You may find similar items within these categories by selecting from the choices below:. Steel Type B – Maximum of 1.

Your 18826 is empty. Find Similar Items This product falls into the following categories. This standard covers hot rolled stainless steel plates rolled on a reversing mill known as quarto plate.

Featured Articles & Publications

If not specified, the manufacturer can supply to either class. There are 3 classes of tolerance for width and length for plates with trimmed edges A – C. Learn more about the cookies we use and how to change your settings. One interpretation of the standard is that no ground area of the plate may fall below the minimum thickness tolerance. For comparison, EN has an edge camber of 0. The flatness tolerance is dependent on grade. This is in contrast to EN which was referred to in EN and allowed some areas to be below minimum thickness.

Sheet materials, Stainless steels, Corrosion-resistant steels, Steels, Hot-working, Rolled products, Dimensions, Dimensional tolerances, Form tolerances, Designations, Dimensional measurement.

In ENthe inscribed rectangle definition was not restricted to plates with untrimmed edges.

  AIPHONE TC-10M PDF

ISO – Hot-rolled stainless steel plates — Tolerances on dimensions and shape

It removes some anomalies and ambiguities from that standard. There 182286 two levels of tolerance normal Class N and special Class S. Therefore, and were given the same flatness tolerance.

This may not be realistic. Provision is made for different width and length tolerances depending on the method of cutting. Shall be agreed at time of enquiry and order. For plate with untrimmed edges in the enquiry and in the purchase order, the edge camber and out of squareness shall be limited so that is is possible to inscribe a rectangle of the nominal length and width of the ordered isl within the delivered size.

This is dependent on the method of cutting the plates.

This website is best viewed with browser version of up isi Microsoft Internet Explorer 8 or Firefox 3. The class shall be specified at the time of enquiry and order. For plate with trimmed edges, the edge camber shall not exceed 0.

Tolerances on 1886 and shape Status: Search all products by. It replaces EN which was not specifically for stainless steel. Office and Postal Address: It is quite difficult to compare the flatness tolerances in EN and ISOas the definition of steel types is totally different.