DATASHEET 2N2219 PDF

The 2N, 2N, 2N and 2N are sili- con planar TO (for 2N and 2N) and in Jedec . This datasheet has been download from. Semelab encourages customers to verify that datasheets are current before Test Conditions. Min. Typ. Max. Unit. LAB. SEME. 2N IC = 10mA. IB = 0. Sep 2. Philips Semiconductors. Product specification. NPN switching transistors. 2N; 2NA. FEATURES. • High current (max.

Author: Yozshugis Fedal
Country: Ecuador
Language: English (Spanish)
Genre: Software
Published (Last): 10 August 2017
Pages: 469
PDF File Size: 15.32 Mb
ePub File Size: 17.32 Mb
ISBN: 358-7-60788-419-6
Downloads: 94239
Price: Free* [*Free Regsitration Required]
Uploader: Kagasida

When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter.

Complete Technical Details can be found at datashfet datasheet given at the end of this page. So if you looking for an NPN transistor that could switch loads or for decent amplification then 2N might the right choice for your project. In our case for a collector current of mA we have to pass a base current of 16mA.

To make this current flow through the transistor the value of base current I B can be calculated using the below formula:. So the value if R Datasheett will be. Here lets us assume the load here consumes around mA maximum so our collector current I C mA. But this calculation will lead to the closest value to start with.

  KARTIKA MAHATMYA PDF

Where h FE, is n22219 current gain of the transistor which in our case is The 2N is a NPN transistor and is normally used as a switch in many circuits. To make this current flow through the transistor the value of base current I B can be calculated using the below formula: The value of this current can be calculated by the required amount of current that will be consumed by the load.

Another important thing to keep in mind, while using a transistor as switch is the base resistor. This resistor is connected to the base pin of the adtasheet to limit the current flowing through the base.

2N2219 Datasheet, Equivalent, Cross Reference Search

Current Drains out through emitter, normally connected to ground. Amplifier modules like Audio datahseet, signal Amplifier etc. Current flows in through collector, normally connected to load.

Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits. This stage is called Saturation Region.

When base 2j2219 is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. Submitted by admin on 21 June As we know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor to turn it on.

  IN THE CITY BY THE SEA BY KAMILA SHAMSIE PDF

2N Transistor Pinout, Specs, Equivalent & Datasheet

Since transistor is of NPN the daatsheet to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below.

To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the base pin.

Where Vcc is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1. So to calculate the resistor value of the base we can use the formulae. TL — Programmable Reference Voltage. But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle.

The maximum amount of current that could flow through the Collector pin is mA, hence datasgeet cannot connect loads that consume more than mA using this transistor. However this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum current from the transistor.