CARDAX 6000 PDF

Cardax FT Controller – Download as PDF File .pdf), Text File .txt) or read online. Installation Guide. Cardax FT Controller CAUTION This equipment contains components that can be damaged by electrostatic discharge. Ensure both you. The Gallagher Controller supports the following door readers: > Cardax IV Prox (Mifare, kHz, TIRIS). > Cardax IV Prox Plus (Mifare, kHz,. TIRIS).

Author: Malahn Gogor
Country: Bhutan
Language: English (Spanish)
Genre: Sex
Published (Last): 15 October 2010
Pages: 272
PDF File Size: 13.71 Mb
ePub File Size: 14.77 Mb
ISBN: 786-8-55625-964-3
Downloads: 11521
Price: Free* [*Free Regsitration Required]
Uploader: Akinolkree

This picture is not to scale, therefore use the measurements provided. The rear optical tamper detector will sense if the Cabinet is removed from its mounting position.

Follow the steps below to access the Controller’s Config web page: Both units are designed to fit into a standard Cardax FT Cabinet together. Integrated Access Control and Intruder Alarms capability 2. Unused For factory testing only. The Enter Network Password screen displays. Shimano tiagra flight deck 600 speed manual Acer travelmate lci driver Ni circuit design suite keygen Documents.

Cardax Ft Controller 6000pdf

On-board termination is optional using termination jumpers. Each device attached to a Cardax FT Controller must be allocated an “address”. Published on Oct View 1. Both variants of the Controller can operate on their own, or can have an optional Reader Module part number C or C connected. There is a proprietary serial communication protocol between the two boards.

Cardax FT for Airport Security.

Unused Unused Boot normally. The power supply cable must be of sufficient size to ensure that the voltage at the GBUS unit terminals is the recommended 12 Vdc. On startup, the main application is run. The red Run LED flashes in the following sequence: Switch on power to the Cardax FT Controller Install all the system and power cables.

  AKTA KETERANGAN SAKSI KANAK-KANAK 2007 PDF

Note that this cable type is only suitable for the communications circuits. Operating temperature Humidity Maximum number of Card readers Intruder Alarms may be installed in elevator cars to Documents.

The security of the installation ultimately depends on the way the Cardax FT Cabinet is installed. This indicates the Cardax FT Controller is waiting for database information to be downloaded from the Server.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Refer to the “Component layout” within this Installation Note for wiring this plug. Cardax FT Key Strengths. Cardax FT Version 5. Standard and High Specis a processing board for an intruder alarm and access control system.

Gallagher Controllers Overview The Gallagher Controllers are intelligent field controllers, programmed to make access control and intruder alarm decisions in the field, independent of the Gallagher Command Center. When the Cardax FT Controller is re-powered after servicing and is operating correctly, the optical tamper detectors will be re-initialised. The Settings in bold specify the default new installation startup configuration.

Cardax Ft Controller pdf

Changes or modifications not expressly approved by Carsax Security Management Systems could void the user’s authority to operate this equipment. Alternatively, an override reset on the Controller can be carried out in Cardax FT Command Centre via the Status and Overrides tab of the Controller properties with the cabinet closed.

This port is provided for external communications to be connected to the system.

  LACTO VEGETARIANO PDF

The Cabinet door must remain closed for at least one minute for the initialisation of the optical tamper detectors to be completed.

Flash Slow Fast 1 flash 2 flashes Sequence timing Meaningms on, ms off Controller is searching for software FTS files ms on, ms off 4Hz flash ms on, ms off 1Hz flash 2 flashes – pause each flash is caedax on, ms off, 1. Carefully lift the Controller clear of the Cabinet.

The In-service relay is used to signal an external alarm if the Controller fails. Set switch 2 to ON closed. However, this DC voltage out will be approximately 1 volt lower than the voltage supplied to the Cardax FT Controller Revert to the factory default version of the operating system.

The following initialisation procedures are detailed in the later section titled “Initialisation”: These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. The termination jumper on either GBUS circuit needs to be fitted if the Controller is the end device for this circuit.

The Gallagher Controller is specifically designed to support access cadrax doors and integrated intruder alarms.

Gallagher Controllers | AES Group Ltd.

Overview The Gallagher Controllers are intelligent field controllers, programmed to make access control and intruder alarm decisions in the field, independent of the Gallagher Command Center.

Cardax FT 600 Documents. The Cardax FT Controller integrates much of the functionality of the original On-board connections are provided for:.