CH C C20 C C CH CH CHA ALPHA CHE .. General Plant/Equipment Reactors – Alloy Atmos Press Bottlers Generator Skôr ako uvediete spotrebi do prevádzky Preítajte si, prosím, pozorne návod na.
|Published (Last):||1 April 2009|
|PDF File Size:||17.36 Mb|
|ePub File Size:||5.59 Mb|
|Price:||Free* [*Free Regsitration Required]|
This is the only procedure that can ensure good door seal! This water then absorbs the excessive energy and exits to the sewer. If such exceeding occurs, it is then necessary to depress the thermostat.
Návod k obsluze – Spotřebiče
Cover their complete surface and front faces so that no cinder may fall behind them. The boiler must always be installed in a way which prevents overheating and subsequent damage even during a power cut.
Take the boiler drum and hood to a scrap-metal collection site. The guarantee period for other parts remains unaffected. Both the pumps may however be switched by just one thermostat. Cover the glowing charcoals with a broad log and add coal or other fuel. It is necessary to seek and discover an optimal position of the thermostat; atmoe depends on type of fuel, chimney draught and other conditions. If you want the ventilator to start operating again, set a lower temperature on nvvod waste gas thermostat e.
Guarantee and post-guarantee period repairs are carried out by: Installation may only be carried out by persons trained by the manufacturer. Slide the grating tube back in position and place the individual segments back on it, one by one. This company shall also complete the boiler installation report p. This thermostat must be pressed down in case that boiler overheating occurred. Ignition valve pulling-rod — is used for opening up the ignition valve during ignition or fuel-loading stage.
Technical description The boilers are designed for burning brown coal and wood. The chimney diameter must not be smaller than the boiler outlet min. The control panel also comprises of a waste gas thermostat which is used to switch the ventilator off when the fuel has been combusted. Opravu provedl, datum CZ www.
The boiler is set to optimal operating parameters by the manufacturer. Connection of these elements is illustrated in the wiring diagram. Flue-gas ducts must be mechanically durable and sealed against combustion products and gas penetration, and it must be possible to clean them inside. Use a screwdriver to remove the old sealing cord and to clean the groove in which it was seated.
The operator ncod occasionally inspect operating boilers. Then remove the door and slightly turn the screw with a righthand thread, as necessary. Set the waste gas thermostat into the operating position which it is necessary to determine for ideal operation.
In order to prevent excessive smoke formation, load new batch of fuel only after the previous fuel has combusted to at least one third of the loading volume. GB Hot-water boiler 2.
If the side play is lower than c20d, reduce one ore more segments by the necessary thickness. Plastic bags, various plastic materials, paints, textiles, laminate are substances which should be particularly avoided but also avoid burning sawdust, sediment and coal dust. By this procedure, the ashes are sifted down to the lower chamber. Another option is purchasing tanks in a leather-cloth housing insulated by mineral wool see the price list.
A control panel for electromechanical regulation is situated in the upper part of the boiler. DN 40, DN 50 www.
When the heating season is over, clean the boiler thoroughly and replace damaged parts. If the installation was not carried out in a professional manner, the subsequent costs are borne by the company that carried out the installation.
Návod k obsluze
The door lock consists of a lever with a handle and a cam which engages a wheel that is screwed into the boiler and secured by a amos preventing its turning. Condensation will disappear later. B ze dne Inlets 1 and 3 always remain open. Otherwise, the ventilator S may sustain damage. Boiler bases We recommend providing a concrete metal base under the boiler. Possible failures and troubleshooting Failure GB Cause – no voltage in network – plug incorrectly inserted to el.
The regulation is based on the pre-set outgoing temperature value. By following these steps in reverse order, you can replace the door.
nvo The chimney draught is directly dependent on its cross-section, height and the inner wall ruggedness. We recommend cleaning the boilers once a week if burn- GB www.
This is only permitted during wintertime. Then remove the front cover and the grating lever. The boilers are equipped with an extraction ventilator the advantage of which is that at the fuel loading stage the smoke generation is reduced.
Otherwise, the boiler and ventilator c20d get covered in tar and their service life would be reduced. If need be, a thermoregulatory valve set to a higher temperature E.