ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.
|Published (Last):||11 September 2007|
|PDF File Size:||17.60 Mb|
|ePub File Size:||2.19 Mb|
|Price:||Free* [*Free Regsitration Required]|
Current edition approved Sept. Type L LN In the annealed condition it is essentially non-magnetic and becomes slightly magnetic with the application of cold work. One bend test shall be made from one end of each coil. D PSS means plate, strip, sheet. A number in parentheses indicates the year of last reapproval. The values given in parentheses are for information only.
In case z666-10 dispute, the offset method of determining yield strength shall be used. Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties.
This standard has been approved a66610 use by agencies of the Department of Defense. Only annealed conditions of grades speci? The values obtained in this manner should not, however, be taken as the actual yield strength for 0. HardC Elongation in 2 in. Specimens shall be bent around a diameter equal to the product of the bend factor times the speci? Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool. C Annealed material that naturally meets mechanical properties may be applied. The choice of test method for materials in conditions other than annealed shall be at the option of the seller. Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres Chemical Composition: Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
and L Stainless Steel – NKS
Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool Corrosion: Rockwell B 95 95 However, in the case of dispute, tests shall be made by pressure. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Heat to o F to o F and cool at sufficiently high rates through oF to oF to avoid precipitation of chromium carbides.
Number of Tests 8. HRC typical L Ann 25 min.
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Types and L are weldable by most fusion or resistance welding techniques.
304 and 304L Stainless Steel
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Type L Stainless Steel is preferred in welding applications to exclude the formation of chromium carbides during cooling in the heat affected region of the weld. B Type is generally produced with a chemical composition balanced for rich side Type aztm lean side Type austenite stability depending on the properties required for speci? Maximum unless otherwise indicated.
Due to the high work hardening rate of these materials, intermediate anneals maybe required to successfully fabricate the part.
ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Permission rights to photocopy the standard may also be secured from the ASTM website www. This revision of Speci? Types and L cannot be hardened by thermal treatment. Originally approved in These alloys represent an excellent combination of corrosion resistance and fabricability. Material Test Report and Certi? The noncontrolling factor normally will exceed considerably the speci? If filler metal is required, Type is normally used.
A — 10 Standard Speci? Types and L provides corrosion resistance in a wide w666-10 of moderately oxidizing and reducing conditions, fresh water and non-marine applications.
Find out what NKS can do for you.