ASTM A386 PDF

ASTM-A › Zinc Coating (Hot-Dip), Assembled Steel Products. ASTM-A – EDITION – SUPERSEDED — See the following: ASTM-. in Specifications A and A This ASTM Standards A47/ A47M 1 This specification is under the jurisdiction of ASTM Committee A05 on. ASTM AAM Standard Specification for Zinc – Standard A and A shall be done using the metric equivalent of the test.

Author: Morn Meztikinos
Country: Saint Kitts and Nevis
Language: English (Spanish)
Genre: Spiritual
Published (Last): 25 May 2015
Pages: 110
PDF File Size: 4.53 Mb
ePub File Size: 6.44 Mb
ISBN: 578-5-12351-605-4
Downloads: 77409
Price: Free* [*Free Regsitration Required]
Uploader: Tojas

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Dynamic Strain Aging of Steels: Materials and Manufacture 5. Practices AAand A provide guidance for steel fabrication for optimum hot dip galvanizing and shall be complied with in both design and fabrication.

ASTM Standard List: Coated Steels

Part Two Medium Manganese Steels: Purchasers desiring a guarantee of heavier coatings than the minimum thicknesses shown herein should use the special requirements see 4.

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

The average of no less than? With Total Materia finding information about a metal standard specification, its current status and the materials it defines is one click away. This standard has been approved for use by agencies of the Department of Defense. In the case of orders in inch-pound units, the measured value shall be converted to coating grade units by the use of Table 2. If the lot is found to be nonconforming by the new sample, the galvanizer has the right to sort the lot for conforming articles by individual test, to re-galvanize nonconforming articles, or to renovate the nonconforming articles in accordance with 6.

Surfaces that remain uncoated after galvanizing shall be renovated in accordance with the methods in Practice A unless directed by the purchaser to leave the uncoated areas untreated for astk renovation by the purchaser.

NOTE 6—The requirements for the? For more information on the ASTM designation system see our related article: NOTE 4—The coating thickness ast, in Table 1 represent the minimum value obtainable with a high level of con?

  LAPSSET PROJECT PDF

Search Knowledge Base Enter a phrase to search for: Metallic coated carbon steel wire coated at size for mechanical springs Composite ribbed steel pipe, pre-coated and polyethylene lined sewer pipe application Flexible poly vinyl chloride PVC gaskets used in connection of water closets to sanitary drainage system For more information on the ASTM designation system see our related article: Unless otherwise agreed upon between the galvanizer and the purchaser, or established 3a86 this speci?

Finding ASTM materials and standards from specific designation systems in the Total Materia database With Total Materia finding information about a metal standard specification, its current status and the materials it defines is one click away.

These designations often apply to specific products, for example A is applicable to cold-heading quality carbon steel wire for tapping or sheet metal screws. Visual inspection of the coating shall be made for compliance with the requirements. Enter a phrase to search for: NOTE 5—Inaccessible surface areas are those which cannot be reached for appropriate surface preparation and application of repair materials as described in Practice A Practice A provides guidance on steel selection and discusses the effects of various elements in steel compositions for example, siliconthat in?

In the case of orders in SI units, such shall be stated to the galvanizer when the order is placed. Inspection, Rejection, and Retest 9. These tests shall not be required unless strong evidence of embrittlement is present.

Introduction to Total Materia Integrator 7 th March It is the responsibility of the purchaser to heat treat or otherwise allow for the possibility of such embrittling phenomena. The other values are based on conversions using the following formulas: In such case, the now-smaller lot shall be treated as a new lot for purposes of inspection and acceptance.

To get started, click on the standard list button in the menu bar. The weight of coating per unit area thus determined is converted to equivalent coating thickness values in accordance with Table 2 rounding up or down as appropriate. The elements can be added to the galvanizing bath as part of a pre-alloyed zinc feed, or they can be added to the bath by the galvanizer using a master feed alloy. Number of Pieces in Lot 3 or less 4 to to 1 1 to 3 3 to 10 10 and over Number of Specimens all 3 5 8 13 20 NOTE 10—Where a number of identical items are to be galvanized, a statistical sampling plan may be desired.

  CAWSON MCQ PDF

This article contains a list of standards that covers among other things: The zinc coating on threaded components of articles galvanized under this speci? Total Materia has allowed us to solve in a definite way all problems we had for the search of alternate materials in foreign countries. If a zinc alloy is used as the primary feed to the galvanizing bath, then the base material used to make that alloy shall conform to Speci? Thanks to Total Materia we have issued real “international” specs for purchase of steels in foreign countries.

Such a plan is contained in Test Method B which addresses sampling procedures for the inspection of electrodeposited metallic coatings and related? This new sample shall be measured using magnetic thickness gages which have been calibrated for accuracy against reference material thickness standards.

For a unit of product whose surface area is equal to or less than in. Inchpound units and SI units are not necessarily exact equivalents. The galvanizing of separate reinforcing steel bars shall be in accordance with Speci?

ASTM AAM Standard Specification for Zinc_百度文库

The thickness of coating thus obtained is the test article coating ast. By simply clicking the materials hot link, you can see a list of metal materials defined by a3386 selected standard. NOTE 2—The presence in steels and weld metal, in certain percentages, of some elements such as silicon, carbon, and phosphorus tends to accelerate the growth of the zinc-iron alloy layer so that the coating may have a matte? Otherwise, the test specimens shall be selected at random from each lot.